Edelbrock 1403 Performer 500 CFM Elect. Carb/Air/Fuel Kit

Top off your engine with these carburetor air/fuel installation kits.  Complete installation kit includes mounting hardware.

Kit Includes:

• (1) Edelbrock 1403 Performer 500 CFM 4 Barrel Carburetor, Electric Choke
• (1) Edelbrock 1208 Pro-Flo Chrome Air Cleaner Assembly, Round, 2 Inch
• (1) Edelbrock 8126 Performer Carb Fuel Line Kit, 3/8 Inch Hose Barb Inlet
• (1) 1-1/2″ Liquid-Filled Fuel Pressure Gauge, 0-15 PSI
• (1) Carburetor Stud Kit, 1-3/8 Inch

Edelbrock 1403 Performer 500 CFM 4 Barrel Carburetor, Electric Choke

• Edelbrock Performer Series carbs have proven themselves to be easy to tune with great drivability
• Whether you need to replace an aging stock four barrel carb or are looking for a performance carb to top off your hot rod, the Edelbrock Performer Series four barrel carbs are the best choice for performance and value
• All Edelbrock products are proudly made in the U.S.A
• Designed and calibrated for smaller cubic-inch engines, so use this Edelbrock carb for Chevy 305 and Ford 302 (or smaller) engines
• Match with an Edelbrock Performer or Performer EPS manifold and other brands of similar design
• This 4 barrel carb includes an electric choke and detailed instructions
• Ford/Mopar throttle adapter arms sold separately

Features:

• Electric choke
• Bolt-on-and-run performance right out of the box
• Smooth throttle response throughout the power band
• Uses metering rods to transition between circuits – rods can be changed in seconds without carburetor removal or draining fuel
• Float levels are factory set; adjustments are rarely needed
• Change jets, adjust floats & replace needles/seats without draining fuel or removing carb
• Two-piece design means no gaskets below the fuel level for leak-free operation
• Lightweight all-aluminum body is compatible with gasohol and blended fuels
• Includes both timed and full vacuum ports for ignition advance

Edelbrock 1208 Pro-Flo Chrome Air Cleaner Assembly, Round, 2 Inch

• Stamped From 18-Gauge Steel
• Triple-Chrome Plated
• High-Quality Finish
• Great Looks
• Works With All 5.125 in. Carbs
• Great for applications with low hood clearance
• Base Knock-Outs For Use w/Crankcase Ventilation
• Adapter For Crankcase Ventilation # 1205 not included, available separately
• 10 Inch diameter
• 2 Inch Filter Height

Edelbrock 8126 Performer Carb Fuel Line Kit, 3/8 Inch Hose Barb Inlet

• 3/8” fuel line kits have a clean look and are easy to install
• Fuel inlets for Edelbrock carburetors provide a clean and custom plumbing solution
• Drop-down design routes the fuel line on the right-hand (passenger side) of the carburetor below the linkage and choke housing
• Includes a barbed end for a push-on 3/8″ rubber fuel line
• Manufactured of chrome plated steel
• Include a 5/8″ -20 threaded banjo bolt with gaskets

1-1/2″ Liquid-Filled Fuel Pressure Gauge, 0-15 PSI

• Appropriate fuel pressure is important for adjusting your fuel system to achieve optimal performance, which means an accurate pressure gauge is equally important
• Built for superior precision
• Liquid filled and available for carbureted and fuel injected applications
• 0-15 PSI
• 1-1/2″ diameter

Carburetor Stud Kit, 1-3/8 Inch

• Easy installation/removal of carb plates
• Includes zinc plated steel studs, nuts and washers
• 1-3/8″ tall

Includes:

• Metering Jets – Primary .086, Secondary .095
• Metering Rods – .065 x .052
• Step-Up Spring – orange (5″ Hg)

Includes:

• Metering Jets – Primary .086, Secondary .095
• Metering Rods – .065 x .052
• Step-Up Spring – orange (5″ Hg)

Edelbrock 500 CFM 4 Barrel Carb Instructions (PDF)

Fuel Line Kit Instruction Sheet (PDF)

Installation Instructions (PDF)